Chamption Moto UK Mens Clothing

Gerbing's Heated Trouser Liner & Insoles

RRP: 239.98
Our Price: 224.95
Buy Today & SAVE: £15.03
Size: Select from the below options
Colour: Black Qty:
Trouser Size:
Insole Size:
Two 12V 1.2Ah Lithium Batteries & Charger £79.95
Portable Temp Controller £57.95
Portable TC & Cover £65.95
Portable Dual Temp Controller £82.95
Portable Dual TC & Cover £92.95
Permanent Temp Controller £64.95
Permanent Dual Temp Controller £94.95
Cable Splitter £7.95
Gerbing Heated Motorbike Clothing



Save £££'s - Gerbings Heated Motorcycle Trouser Liner & Insoles combo deal



Great savings to be had this winter on this Gerbing heated motorbike clothing combination deal.



Heated Motorcycle Trouser Liner


  • Compressible, water-repellent, durable, Thinsulate® insulation
  • Teflon® coated, wind-resistant, soft nylon shell
  • Form-fitting patterns and sizing to fit snugly and easily under your outer garments
  • Full length zipper from hip to bottom of pant for each side
  • Lifetime warranty on the heating elements



Note:  These heated motorcycle trouser liners are worn underneath your regular motorcycling trousers/jeans/slacks/pants/pantalons/etc.



How it Works







Heat                 Microwire® Heat Technology
Source             12-volts DC
Current            3.6 amps
Watts               44 watts
Surface Temp   125°F +/- 5°F at 32°F




Hips Size:  This is your HIP measurement, not your waist.  Measure around fullest point of seat while standing.  The following table shows your Hips Size based on your Hips Measurement.


Belt to Floor Size:  Measure along the outer seam from the top of the belt down to the floor with shoes on.  The following table shows your Belt-to-Floor Size based on this measurement.


 Hip Size (inches)
 Belt to Floor (inches)
 Trouser Liner Size







Gerbing Heated Motorcycle Boot Insoles


We've all had cold feet sometime in our lives. We're talking REAL cold, not just wedding-day jitters.  Cold, stiff, tender feet can turn any ride into a miserable one.  But these heated boot insoles from Gerbing Heated Motorbike Clothing range are designed to deliver powerful, warming heat and unlike the other heated insoles, provide heat over their entire surface area. They'll be a valuable addition to your winter motorbike gear.


They'll keep your feet toasty warm, on or off the bike.  Because Gerbing's Hybrid Heated Insoles are designed to connect to your other Gerbing's Heated Gear, you can run them straight off any vehicle's 12V DC power source e.g. bike, car, snowmobile, ATV & electric wheel chair batteries, or you can power them off one of Gerbing's rechargeable lithium battery packs (4,0A LiPo battery - optional).


There is a lifetime warranty on the heating elements.





  • One Glove/Sock Harness
  • One Fused Battery Harness







  • Utilizes Gerbing's Hybrid Heating System
  • Power directly from a 12v electrical system, or
  • Power them from an optional 12v Lithium battery pack
  • Includes one free fused battery harness and Y-harness
  • Heats entire surface area
  • Lifetime warranty on the heating elements
  • Incorporates Gerbing's Microwire® heating technology that uses micro-sized heating fibers to surround the foot with warmth





Heat         Microwire® heat technology
Source     12-volts DC
Current    1.2 amps/pair
Watts      15 watts



Sizes:  The insoles are each marked with two guide lines to cut them to size.  If you're not sure which of two sizes to buy, get the larger and if necessary you can cut them to size.  Do not venture beyond the inner guide line, especially if plugged in to the mains!  Once cut, we will be unable to accept return.


Mens Boots:

 UK Size
3-4 4½-5½ 6½-7½ 8-8½ 10-11 11½-12½
 EU Size
37-38 40-41 42-43 44-45 46-47
 = Insole Size







Ladies Boots:

 UK Size
2½-3½ 4-5 6-7 7½-8 9½-10½ 11-12
 EU Size
37-38 39-41 42-43 44-45 46-47
 = Insole Size







N.B.  Sizes on the insoles' packaging are U.S. sizes




Temperature Controllers:


The jacket as delivered is ready to go, i.e. you need not purchase any accessories to make it work.  Insoles plug into the trousers, trousers into the jacket and the jacket to the bike.  Gloves can either plug into your jackets dual controller or a single controller with a splitter. 


In the absence of a temperature controller, temperature is controlled only by plugging/unplugging from the bike.  If you're not up for a temp. controller, then for convenience we recommend buying the Lighted On/Off Switch.  Think; the flick of a switch vs. unplugging electrical connectors!


The purpose of Temp. Controllers is to allow the rider to vary the heat output.  Dial in your comfort level with a simple turn of the dial!  Unlike older rheostat type thermostats, Gerbing's digital temp controllers draw just enough current to maintain the heat you need.  Temp. Controllers allow you to adjust for your desired heat output of all 12v products, but are not designed to be used with 7v products. 


The single temp. controller sets the same temperature for all clothing items.  With the dual controller, the gloves are on a different circuit from the jacket, trousers and insoles and thus can be set to a different temperature.  This is very useful as hands seem to suffer most from wind chill.  So you can keep your hands toasty warm whilst not getting a sweat on elsewhere!  Permanent controllers are set into the fairing panel and requires 'hole drilling'! 


For more information on controllers, Click on the links below.  Select your preference from the accessory list at the top of this page.


Portable Controller and cover

Portable Dual Controller and cover

Permanent Controller

Permanent Dual Controller


Note: If you are purchasing a single controller to use with one of the jackets that are wired with the Dual 2 wiring systems, you will need to purchase a splitter if you choose to operate other heated clothing with the jacket.



Shopping Cart
Choose Currency Checkout
Your Account
Username Password New Customer Forgot Password
Advanced Search
Order Now 02920 807614 Payment Options Sage Pay & PayPal Comodo EV SSL Certifictaed