Chamption Moto UK Mens Clothing

Gerbing's Heated Trouser Liner & Hybrid Gloves

RRP: 319.98
Our Price: 304.95
Size: Select from the below options
Colour: Black Qty:
Trouser Size:
Glove Size:
Two 12V 1.2Ah Lithium Batteries & Charger £79.95
Portable Temp Controller £57.95
Portable TC & Cover £65.95
Portable Dual Temp Controller £82.95
Portable Dual TC & Cover £92.95
Permanent Temp Controller £64.95
Permanent Dual Temp Controller £94.95
Cable Splitter £7.95
FREE Junior Temperature Controller
Gerbings Heated Motorcycle Trouser Liner & T5 Heated Motorcycle Gloves



Save with this Gerbings Heated Motorcycle Trouser Liner
& Hybrid Heated Motorcycle Gloves combo deal



With FREE UK Mainland P&P and

FREE Gerbing Junior Temperature Controller 



Great savings to be had this winter on this heated motorcycle clothing combination deal.



Heated Motorcycle Trouser Liner


  • Compressible, water-repellent, durable, Thinsulate® insulation
  • Teflon® coated, wind-resistant, soft nylon shell
  • Form-fitting patterns and sizing to fit snugly and easily under your outer garments
  • Full length zipper from hip to bottom of pant for each side
  • Lifetime warranty on the heating elements



Note:  This heated motorcycle trouser liner is worn underneath your regular motorcycling trousers/jeans/slacks/pants/pantalons/etc.



How it Works







Heat                 Microwire® Heat Technology
Source             12-volts DC
Current            3.6 amps
Watts               44 watts
Surface Temp   125°F +/- 5°F at 32°F




Hips Size:  This is your HIP measurement, not your waist.  Measure around fullest point of seat while standing.  The following table shows your Hips Size based on your Hips Measurement.


Belt to Floor Size:  Measure along the outer seam from the top of the belt down to the floor with shoes on.  The following table shows your Belt-to-Floor Size based on this measurement.


 Hip Size (inches)
 Belt to Floor (inches)
 Trouser Liner Size






Gerbing Hybrid Heated Motorcycle Gloves


Gerbing's innovative and revolutionary new Microwire® heated motorcycle gloves.  The best of two worlds.  This system allows you the option of powering these winter motorcyle gloves from your vehicle's 12 volt electrical system, or from Gerbing's 12 volt lithium-ion battery pack with its built-in microprocessor temp controller.


If you're cruising for hours, just connect these gloves the usual way, with Gerbing's battery hook-up.  Just riding for an hour?  Plug in the small portable batteries.


A comfortable leather motorbike glove made with an exceptionally soft and supple drum-dyed premium leather that contours to the hand.  The design is sleek, stylish and very functional as a light, but strong and pliable glove.  Because of the use of Stainless Steel heating wire, it is  the most durable glove in the world!


  • Made with premium, supple, drum-dyed leather
  • Incorporates Gerbing's Microwire® heating technology that uses micro-sized heating fibers to surround the hand with warmth
  • Heats the entire length of each finger, including the thumb, as well as the back of the hand within seconds after plugging in
  • Waterproof/windproof/breathable Hipora® liner to provide protection from water and wind
  • Adjustable wrist enclosure
  • Thinsulate® insulation and brushed liner for added warmth and comfort
  • No feeling of the heating wire, because of Microwire® Heating Technology
  • Lifetime warranty on the heating elements
  • FREE inline Junior Temperature Controller for controlling the heat

Gloves include: battery hook-up & harness and FREE Junior Temperature Controller


Cable Splitter:  If you intend to connect the gloves to the Gerbing Heated Jacket Liner or Single Temperature Controller, then you will need a Cable Splitter to enable the jacket and gloves to be heated at the same time.  Please select it from the Options List.





Heat:               Microwire
Source:           12V DC
Current:          2.2A
Watts:             27
Surface Temp  57°C/135°F (±2°C/5°F at 0°C/32°F)



Batteries & Charger: Two portable 12V 1.2Ah Lithium batteries with built-in microprocessor temp. controller and a charger are optional.  If required, please select from the options at the top of the page.  Shipping is free when purchased with the gloves.


Approximate battery capacity per charge for 12 V hybrid glove batteries


Power Level                            Run Time
High                                        1 hour
Medium                                   2 hours
Low                                        3 hours
Connected to Vehicle Battery  unlimited


* Actual run time may vary depending on ambient temperature.  Battery capacity decreases in very cold weather, especially if the battery is not insulated, and is left exposed to the elements.  At less than 32 degrees Fahrenheit a battery may only produce 80% of its capacity.



Hand Measurement:  Measure around flat hand at knuckles, thumb excluded.  Use this measurement to determine your glove size.  


Glove Size: The following table shows a Glove Size based on your hand measurement.


 Hand Size (cms)
 Glove Size






Temperature Controllers:


The gloves come with a free Junior Temperature Controller.


The jacket as delivered is ready to go, i.e. you need not purchase any accessories to make it work.  Insoles plug into the trousers, trousers into the jacket and the jacket to the bike.  Gloves can either plug into your jackets dual controller or a single controller with a splitter. 


In the absence of a temperature controller, temperature is controlled only by plugging/unplugging from the bike.  If you're not up for a temp. controller, then for convenience we recommend buying the Lighted On/Off Switch.  Think; the flick of a switch vs. unplugging electrical connectors!


The purpose of Temp. Controllers is to allow the rider to vary the heat output.  Dial in your comfort level with a simple turn of the dial!  Unlike older rheostat type thermostats, Gerbing's digital temp controllers draw just enough current to maintain the heat you need.  Temp. Controllers allow you to adjust for your desired heat output of all 12v products, but are not designed to be used with 7v products. 


The single temp. controller sets the same temperature for all clothing items.  With the dual controller, the gloves are on a different circuit from the jacket, trousers and insoles and thus can be set to a different temperature.  This is very useful as hands seem to suffer most from wind chill.  So you can keep your hands toasty warm whilst not getting a sweat on elsewhere!  Permanent controllers are set into the fairing panel and requires 'hole drilling'! 


For more information on controllers, Click on the links below.  Select your preference from the accessory list at the top of this page.


Portable Controller and cover

Portable Dual Controller and cover

Permanent Controller

Permanent Dual Controller


Note: If you are purchasing a single controller to use with one of the jackets that are wired with the Dual 2 wiring systems, you will need to purchase a splitter if you choose to operate other heated clothing with the jacket.


Shopping Cart
Choose Currency Checkout
Your Account
Username Password New Customer Forgot Password
Advanced Search
Order Now 02920 807614 Payment Options Sage Pay & PayPal Comodo EV SSL Certifictaed